[Tinyos-help] MIB520 Micaz Install problem

[Bernardo Avila Pires]

I don't know about the failure to enter programming mode, but if the
problem that is causing this error is not the same causing the others,
they could be due to not seating the motes properly on the board
(which caused me many problems in the past). Have you tried with other
motes (other micaz's and other types)?

2007/7/3, Mayur Maheshwari <mayur.maheshwari at gmail.com>:
> All,
> Has anyone tried installing apps on MicaZ using MIB520 in TOS2?
> I tried installing the Blink app on MicaZ using MIB520 and ran into few
> problems. I am using TOS2 and since MIB520 is not defined in the makerule I
> am issuing 'MIB510' in the command. I have the ports COM7 and COM8.  Also,
> the nature of the error keeps on changing.
>
> Mayur Maheshwari at workstation /opt/tinyos-2.x/apps/Blink
> $ make micaz reinstall mib510,COM7
> cp build/micaz/main.srec build/micaz/main.srec.out
>     installing micaz binary using mib510
> uisp -dprog=mib510 -dserial=COM7 --wr_fuse_h=0xd9 -dpart=ATmega128
> --wr_fuse_e=f
> f  --erase --upload if=build/micaz/main.srec.out
> Please use /dev/ttyS6 rather than COM7 (the latter often doesn't work)
> Firmware Version: 1.8
> An error has occurred during the AVR initialization.
>  * Target status:
>    Vendor Code = 0xff, Part Family = 0xff, Part Number = 0xff
>
> Probably the wiring is incorrect or target might be `damaged'.
> make: *** [program] Error 2
>
> Mayur Maheshwari at workstation /opt/tinyos-2.x/apps/Blink
> $ make micaz reinstall mib510,COM7
> cp build/micaz/main.srec build/micaz/main.srec.out
>     installing micaz binary using mib510
> uisp -dprog=mib510 -dserial=COM7 --wr_fuse_h=0xd9 -dpart=ATmega128
> --wr_fuse_e=f
> f  --erase --upload if=build/micaz/main.srec.out
> Please use /dev/ttyS6 rather than COM7 (the latter often doesn't work)
> Firmware Version: ►.►
> Failed to enter programming mode.
> make: *** [program] Error 2
>
> Mayur Maheshwari at workstation /opt/tinyos-2.x/apps/Blink
> $ make micaz reinstall mib510,/dev/ttyS6
> cp build/micaz/main.srec build/micaz/main.srec.out
>     installing micaz binary using mib510
> uisp -dprog=mib510 -dserial=/dev/ttyS6 --wr_fuse_h=0xd9 -dpart=ATmega128
> --wr_fu
> se_e=ff  --erase --upload if=build/micaz/main.srec.out
> Firmware Version: ►.►
> Failed to enter programming mode.
> make: *** [program] Error 2
>
> Mayur Maheshwari at workstation /opt/tinyos-2.x/apps/Blink
> $ make micaz reinstall mib510,/dev/ttyS6
> cp build/micaz/main.srec build/micaz/main.srec.out
>     installing micaz binary using mib510
> uisp -dprog=mib510 -dserial=/dev/ttyS6 --wr_fuse_h=0xd9 -dpart=ATmega128
> --wr_fu
> se_e=ff  --erase --upload if=build/micaz/main.srec.out
> Firmware Version: 1.8
> Probably the AVR MCU is not in the RESET state.
> Check it out and run me again.
> make: *** [program] Error 2
>
> Mayur Maheshwari at workstation /opt/tinyos-2.x/apps/Blink
> $ make micaz reinstall mib510,/dev/ttyS6
> cp build/micaz/main.srec build/micaz/main.srec.out
>     installing micaz binary using mib510
> uisp -dprog=mib510 -dserial=/dev/ttyS6 --wr_fuse_h=0xd9 -dpart=ATmega128
> --wr_fu
> se_e=ff  --erase --upload if=build/micaz/main.srec.out
> Firmware Version: ►.►
> Failed to enter programming mode.
> make: *** [program] Error 2
> Any suggestions?
>
> Thanks for all your help!
> Regards
> --
> Mayur Maheshwari(mayur.maheshwari at ieee.org )
>
> "Karmanye Vadhikaraste Ma Phaleshu Kadachana,
> Ma Karma Phala Hetur Bhurmatey Sangostva Akarmani"
> _______________________________________________
> Tinyos-help mailing list
> Tinyos-help at Millennium.Berkeley.EDU
> https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
>


-- 
"The truth shall set you free"
<a href="http://www.nerdtests.com/nq_ref.html">
<img src="http://www.nerdtests.com/images/badge/dc875a1ab1aff18f.gif"
alt="I am nerdier than 99% of all people. Are you a nerd? Click here
to find out!"></a>