[Tinyos-help] MIB600 115200

[Yong, Chee Yeew]

I believe that you can use the Lantronix Device Installer to look up any
MIB600s connected to a LAN. I don't know what protocol it uses to do this,
but perhaps Crossbow can explain this?

I do sometimes find that you can probe and find a MIB600 even if it is not
on the same IP subnet. Again, I don't know what are the circumstances that
this will definitely work. Perhaps if you are both connected on the same
network switch/hub?

By the way, you can set the MIB600's IP address using the Lantronix Device
Installer.

> -----Original Message-----
> From: tinyos-help-bounces at Millennium.Berkeley.EDU
> [mailto:tinyos-help-bounces at Millennium.Berkeley.EDU]On Behalf Of
> Bernardo Avila Pires
> Sent: 03 October 2007 01:49
> To: Giri Baleri
> Cc: tinyos-help at Millennium.Berkeley.EDU
> Subject: Re: [Tinyos-help] MIB600 115200
> 
> 
> The problem is that I set its IP address via 'arp' command, using its
> MAC address.
> 
> 2007/10/2, Giri Baleri <mbaleri at xbow.com>:
> > If you know the IP address, you can look it up in Lantronix device
> > installer and make a note of the corresponding MAC address.
> >
> > Giri
> >
> > -----Original Message-----
> > From: Bernardo Avila Pires [mailto:obernardo at gmail.com]
> > Sent: Tuesday, October 02, 2007 12:15 PM
> > To: Giri Baleri
> > Cc: JeongKwanhee; tinyos-help at millennium.berkeley.edu
> > Subject: Re: [Tinyos-help] MIB600 115200
> >
> > Talking about MIB600, dos anyone know how to find out the 
> MAC address of
> > one of these? There's one here whose address has faded from 
> the board.
> >
> > 2007/10/2, Giri Baleri <mbaleri at xbow.com>:
> > >
> > >
> > > Here's what you need to do to change the default baud 
> rates for the
> > MIB600.
> > >
> > > 1. Open a web browser and type the IP address of MIB600. 
> You should
> > > see Lantronix web manager page.
> > > 2. From the left hand menu corner, click on Channel 1 and and the
> > > default settings should be:
> > >     Serial Port Speed: 115200
> > >     Port :10001
> > >
> > > 3. From the left hand menu corner, click on Channel 2 and 
> the default
> > > settings should be:
> > >     Serial Port Speed: 57600
> > >     Port:10002
> > >
> > > 4. If you make changes above, save/update the settings.
> > >
> > > I hope that helps,
> > > Giri
> > >
> > >  ________________________________
> > >  From: tinyos-help-bounces at Millennium.Berkeley.EDU
> > > [mailto:tinyos-help-bounces at Millennium.Berkeley.EDU] On Behalf Of
> > > JeongKwanhee
> > > Sent: Tuesday, October 02, 2007 6:19 AM
> > > To: tinyos-help at Millennium.Berkeley.EDU
> > > Subject: [Tinyos-help] MIB600 115200
> > >
> > >
> > >
> > >
> > >
> > > Hello! Everybody.
> > >
> > >
> > >
> > > I am trying to change the baud rate from 57600 to 115200 
> on MIB600.
> > >
> > > However, I cannot operate correctly. I do not know why it is not
> > running.
> > >
> > >
> > >
> > > So, I will write down about my trial for changing rate.
> > >
> > > First, I tried.
> > >
> > > In eprb.extra  file, I added -dport=10001 on uisp programming.
> > >
> > > .....is not run..
> > >
> > >
> > >
> > > Second, I tried.
> > >
> > > I changed HPLUART0M.nc file as follows.
> > >
> > > outp(15, UBRR0L) -> outp(7, UBRR0L)
> > >
> > > ...is not run..
> > >
> > >
> > >
> > > At result of my test, it always runs just to 10002 port(57600bps).
> > >
> > >
> > >
> > > If somebody know how to change the baud rate, please 
> reply to this.
> > >
> > >
> > >
> > > Thank you
> > > _______________________________________________
> > > Tinyos-help mailing list
> > > Tinyos-help at Millennium.Berkeley.EDU
> > > 
> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-he
> > > lp
> > >
> >
> >
> > --
> > "The truth shall set you free"
> >
> 
> 
> -- 
> "The truth shall set you free"
> _______________________________________________
> Tinyos-help mailing list
> Tinyos-help at Millennium.Berkeley.EDU
> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/t
inyos-help

*******************************************************************************
Please consider the environment before printing this email.
*******************************************************************************
This email and any files transmitted with it are intended solely for the use of
the individual or entity to whom they are addressed and may not be divulged to
any third party without the express permission of the originator.  Any views
expressed in this message are those of the individual sender, except where the
sender specifically states them to be the views of Thales Research & Technology
(UK) Limited.
*******************************************************************************