[Tinyos-help] Re: Using a USB port to connect to a MIB510
Giri Baleri
mbaleri at xbow.com
Thu Oct 4 11:24:10 PDT 2007
I don't think that the Mote is dead.
The "uisp -dprog=dapa... " in the output indicates that the uisp is
trying to use the parallel port (printer port) instead of serial
port(RS-232) that MIB510 is connected to.
Depending on the TinyOS version you are using, you need to specify the
programmer and port number accordingly in the command line.
Regards,
Giri
-----Original Message-----
From: tinyos-help-bounces at Millennium.Berkeley.EDU
[mailto:tinyos-help-bounces at Millennium.Berkeley.EDU] On Behalf Of
Jeongyeup Paek
Sent: Thursday, October 04, 2007 9:55 AM
To: Khew U-Wei
Cc: aneekat patkar; tinyos-help at Millennium.Berkeley.EDU
Subject: Re: [Tinyos-help] Re: Using a USB port to connect to a MIB510
The mote seems to be dead. Try changing the mote.
Thanks
Khew U-Wei wrote:
> Hi Aneekat,
>
> I tried the above command you provided: $ make mica2 install.0
> mib510,/dev/ttyS6
> for a COM7 port and this is my error report:
>
> compiled TOSBase to build/mica2/main.exe
> 9022 bytes in ROM
> 584 bytes in RAM
> avr-objcopy --output-target=srec build/mica2/main.exe
> build/mica2/main.srec make mica2 reinstall.0 PROGRAMMER="DAPA"
> PROGRAMMER_FLAGS="-dprog=dapa -dpart=AT
> mega128 --wr_fuse_e=ff "
> make[1]: Entering directory
> `/cygdrive/c/tinyos/cygwin/opt/tinyos-1.x/apps/TOSBa
> se'
> installing mica2 binary
> set-mote-id build/mica2/main.srec build/mica2/main.srec.out `echo
> reinstall.0 |p erl -pe 's/^reinstall.//; $_=hex if /^0x/i;'` uisp
> -dprog=dapa -dpart=ATmega128 --wr_fuse_e=ff --erase pulse Atmel AVR
> ATmega128 is found.
> Erasing device ...
> pulse
> Reinitializing device
> Atmel AVR ATmega128 is found.
>
> Fuse Extended Byte set to 0xff
> sleep 1
> uisp -dprog=dapa -dpart=ATmega128 --wr_fuse_e=ff --upload
> if=build/mica2/main.s rec.out pulse Atmel AVR ATmega128 is found.
> Uploading: flash
>
> Fuse Extended Byte set to 0xff
> sleep 1
> uisp -dprog=dapa -dpart=ATmega128 --wr_fuse_e=ff --verify
> if=build/mica2/main.s rec.out pulse Atmel AVR ATmega128 is found.
> Verifying: flash
> flash error at address 0x0: file=0x0c, mem=0x00 flash error at address
> 0x1: file=0x94, mem=0x00 flash error at address 0x2: file=0xbc,
> mem=0x00 flash error at address 0x3: file=0x01, mem=0x00 flash error
> at address 0x4: file=0x0c, mem=0x00 flash error at address 0x5:
> file=0x94, mem=0x00 flash error at address 0x6: file=0xd9, mem=0x00
> flash error at address 0x7: file=0x01, mem=0x00 flash error at address
> 0x8: file=0x0c, mem=0x00 flash error at address 0x9: file=0x94,
> mem=0x00 continued....
>
> Do you know whats the problem? Looking forward to your reply. THank
you.
>
> Best regards,
> U-Wei
>
> On 9/28/07, *aneekat patkar* <aneeket007 at yahoo.co.in
> <mailto:aneeket007 at yahoo.co.in>> wrote:
>
> Hi U-Wei,
>
> I install the code by the command "make mica2 install
mib510,/dev/ttyS0"
> for mica2 sensor and with the mib510 programming board. In the
> Cygwin environment you go to the application folder and then type
> this command .
> The digit in "Sx" is generally 1 less than the actual port number
in
> the computer configuration.
>
> What i meant was if S3 doesn't work when the computer says COM4
for
> the cable , then type the command again with S4.
> At a time u can program with only port in a Cygwin window. If you
> have mutliple windows open, then u could program different ports
at
> the same time.
> Hope this helps,
> Aneeket.
>
>
> */Khew U-Wei <khewuwei at gmail.com <mailto:khewuwei at gmail.com>>/*
wrote:
>
> Hi Aneeket,
>
> As you previously said "if COM4 is displayed try "S3" and then
> "S4" when you install the tinyOS code."
> How do you use two different ttys when installing the code on
> the nodes?
>
> Best regards,
> U-Wei
>
> Date: Mon, 24 Sep 2007 12:55:33 -0700 (PDT)
> From: aneekat patkar < aneeket007 at yahoo.co.in
> <mailto:aneeket007 at yahoo.co.in>>
> Subject: [Tinyos-help] RE: Using a USB port to connect to a
MIB510
> To: tinyos-help at millennium.berkeley.edu
> <mailto:tinyos-help at millennium.berkeley.edu>
> Message-ID: < 74051.98657.qm at web8902.mail.in.yahoo.com
> <mailto:74051.98657.qm at web8902.mail.in.yahoo.com>>
> Content-Type: text/plain; charset="iso-8859-1"
>
> The problem is with the digit to be put after "ttys0 " in
>
> MIB510='/dev/ttys0' make mica2 install.0 mib510
> By S0 you refer to the COM1 port which is a 9-pin serial port
.
> To get the correct port number do the following :
> 1. RIght-click on My Computer and click on Properties.
> 2. Go to hardware and then Device Manager.
> 3. The click on Ports .
>
> Your USB to serial port number would be displayed here. If
COM4
> is displayed try "S3" and then "S4" when you install the
tinyOS
> code.
>
> Also if you are gonna read any sensor readings from the serial
> port, set the baud rate and other protocol options by
> "right-click " on the displayed port number and selecting
> properties.
>
> Hope this helps,
> Aneeket.
>
>
>
------------------------------------------------------------------------
> Need a vacation? Get great deals to amazing places
>
<http://us.rd.yahoo.com/evt=48256/*http://travel.yahoo.com/;_ylc=X3oDMTF
hN2hucjlpBF9TAzk3NDA3NTg5BHBvcwM1BHNlYwNncm91cHMEc2xrA2VtYWlsLW5jbQ-->on
> Yahoo! Travel.
>
>
>
>
> --
> "Your future depends on your dreams"
> So go to sleep
>
>
> The more you learn, the more you know, The more you know, the more you
> forget The more you forget, the less you know So.. why learn.
>
>
>
------------------------------------------------------------------------
>
> _______________________________________________
> Tinyos-help mailing list
> Tinyos-help at Millennium.Berkeley.EDU
>
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
--
Jeongyeup Paek
Ph.D. student
Embedded Networks Laboratory
Department of Computer Science
University of Southern California
http://enl.usc.edu/~jpaek
_______________________________________________
Tinyos-help mailing list
Tinyos-help at Millennium.Berkeley.EDU
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
More information about the Tinyos-help
mailing list