[Tinyos-help] Help to fix the flash error at address

[Underléa Cabreira Corrêa]

Dear all,

I 'm just getting start with TinyOS and Mica Motes platform, but I already
have got a problem in the first lesson from tutorial.
I m using TinyOS 2.x in a Linux Ubunto machine. I have followed the
installation instruction from
http://www.tinyos.net/tinyos-2.x/doc/html/install-tinyos.html. I have tested
my environment with $ tos-check-env and I just have got a warning about the
GraphViz version ...
My problem is : I can t install the Blink app on Mica2. Every time I have
tried I have got the following flash error address :(

root at besouro:/opt/tinyos-2.x/apps/Blink# make mica2 install, 1 MIB510,
/dev/ttyS0
mkdir -p build/mica2
    compiling BlinkAppC to a mica2 binary
ncc -o build/mica2/main.exe -Os -finline-limit=100000 -Wall -Wshadow
-Wnesc-all -target=mica2 -fnesc-cfile=build/mica2/app.c -board=micasb
-DIDENT_APPNAME=\"BlinkAppC\" -DIDENT_USERNAME=\"root\"
-DIDENT_HOSTNAME=\"besouro\" -DIDENT_USERHASH=0xcc8c50dfL
-DIDENT_TIMESTAMP=0x48641421L -DIDENT_UIDHASH=0x39bb344dL -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/mica2/wiring-check.xml BlinkAppC.nc -lm
    compiled BlinkAppC to build/mica2/main.exe
            7130 bytes in ROM
              52 bytes in RAM
avr-objcopy --output-target=srec build/mica2/main.exe build/mica2/main.srec
avr-objcopy --output-target=ihex build/mica2/main.exe build/mica2/main.ihex
    writing TOS image
cp build/mica2/main.srec build/mica2/main.srec.out
    installing mica2 binary with dapa
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff  --erase
pulse
Atmel AVR ATmega128 is found.
Erasing device ...
pulse
Reinitializing device
Atmel AVR ATmega128 is found.

Fuse High Byte set to 0xd9

Fuse Extended Byte set to 0xff
sleep 1
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff  --upload
if=build/mica2/main.srec.out
pulse
Atmel AVR ATmega128 is found.
Uploading: flash

Fuse High Byte set to 0xd9

Fuse Extended Byte set to 0xff
sleep 1
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff  --verify
if=build/mica2/main.srec.out
pulse
Atmel AVR ATmega128 is found.
Verifying: flash
flash error at address 0x0: file=0x0c, mem=0xff
flash error at address 0x1: file=0x94, mem=0xff
...
flash error at address 0x2: file=0x49, mem=0xff
I have tried the suggestions that I found on this list but no one have fixed
my problem :(
Any suggestion ?
Thank you so much!!

-- 
Léa

<http://www.das.ufsc.br/%7Eunderlea/>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://www.millennium.berkeley.edu/pipermail/tinyos-help/attachments/20080627/faec8746/attachment.htm